- Equipment
- Downloads
Graco T1 Transfer Pump
Graco T1 pumps maintain performance in any environment, even with higher viscosity materials. Spend more time spraying and less time on maintenance with the Graco 2:1 transfer pumps.
Features:
- The O-ring seal design is more durable and lasts longer - more spraying uptime and less time on maintenance
- Provide consistent feed pressures and flow rates for dependable results
- Lower pressure drops with higher viscosity materials at any ambient temperature
- Designed and manufactured by the worldwide leader in pump technology
- Quick disconnect bung adapter
- Fits 7' job trailers
- Improved o-ring seal design
- Designed to handle viscous materials
- Corrosion-resistant stainless steel wetted parts
Materials:
- Isocyanates
- Catalysts
- Adhesives
- Resins
- Polyurea
- Polyurethane
Applications:
- Plural component material supply
- Polyurea coatings
- Polyurethane foam
- Fluid transfer
- Tank and pipe linings
Highlights:
- Longer lasting pump - designed for durability with less maintenance
- Quick-release bung adapter for easy drum removal without interference from hose connections
- Stainless steel watted parts for corrosion resistance
- PTFE seals for improved performance and less maintenance
Graco Heated Hoses - 2000 PSI
A vital component of a spray foam insulation system is the Graco 2000 psi Heated Hoses. A Graco Reactor paired with Graco's heated hose provides an unparalleled level of performance.
Graco's 2000 psi Heated Hose Features:
- A and B hoses have different fittings to prevent incorrect connections
- Low permeability to avoid crystallization and other chemical reactions of the materials in the lines
- Reduced injury risk with low voltage hose
- Copper wire wound technology produces rapid heating
Graco Heated Hoses - 3500 PSI
A vital component of a contractor's protective coating system are the Graco 3500 psi Heated Hoses. A Graco Reactor paired with Graco's heated hose provides an unparalleled level of performance.
Graco's 3500 psi Heated Hose Features:
- A and B hoses have different fittings to prevent incorrect connections
- Low permeability to avoid crystalization and other chemical reactions of the materials in the lines
- Reduced injury risk with low voltage hose.
- Copper wire wound technology produces rapid heating
Graco T2 Transfer Pump
Graco T2 Transfer Pump
Rely on the Graco T2 pump for increased output and longer life
Graco T2 transfer pumps maintain performance in any environment and are tested and proven to last 15 times longer than the competition, even with higher viscosity materials. Spend more time spraying and less time on maintenance with the Graco T2 2.25:1 transfer pumps.
Features:
Graco T2 transfer pumps maintain performance in any environment and are tested and proven to last 15 times longer than the competition, even with higher viscosity materials. Spend more time spraying and less time on maintenance with the Graco T2 2.25:1 transfer pumps.
Features:
- Improved fluid intake easily handles higher viscosity materials - even in cold conditions
- An improved seal design for better performance and less maintenance downtime
- Combines the best features of Graco and Gusmer 2.25:1 transfer pumps
- Lower pressure drop with higher viscosity materials at any ambient temperature
- Reliable and cost-effective
Applications:
- Plural component material supply
- Polyurea coatings
- Polyurethane foam
- Fluid transfer
- Tank and pipe linings
Highlights:
- Consistent feed pressures and flow rates for consistent results
- Longer lasting pump - re-designed for long-lasting durability with less maintenance
- Quick-release bung adapter for easy drum removal without interference from hose connections
- Stainless steel wetted parts for corrosion resistance
- PTFE seals for improved performance and less maintenance
Graco T3 Transfer Pump
Graco T3 Transfer Pump
The T3 Transfer Pump combines Graco's proven Merkur air-motor and popular T2 lower. The T3 is a 3:1 ratio pump - thereby using less air pressure to provide the same fluid pressure required.
Specifications:
- Easier to maneuver - The overall height of the T3 is 3.7 inches shorter above the drum than the T2 and 2.5 inches shorter than the T1, making it easier to remove from the drum inside of a spray rig.
- More quiet - Studies show the T3 Transfer Pump is about 3x quieter than the T2 Transfer Pump.
- Less Maintenance - the Merkur air-motor is based on air pilot valve technology. The air-motor switching is purely pneumatic. Resulting in fewer parts to wear. (Different from T1 and T2 Transfer Pumps, which use a mechanical reversing mechanism in the air-motor. )
Specifications:
- Rated for a continuous output of 4.5 gpm (17 lpm). Allowing enough flow to easily keep up with Graco's biggest proportioner, the H-50.
- Rated for a max inlet pressure of 100 psi (6.8 bar, 0.68 MPa). An air regulator is included with every pump.
- Available in both Carbon Steel and SST Models.
Graco Husky 1050
Expanded Offering: Materials
- New poly and conductive poly center housings
- Aluminum, poly, conductive poly, PVDF, SST, and Hastelloy fluid sections
- Wide range of materials for balls, seats, diaphragms
Husky 1050 Options:
- Aluminum, Aluminum
- Aluminum, Stainless Steel
- Aluminum, Polypropylene
- Aluminum, Conductive Poly
- Polypropylene, Polypropylene
- Polypropylene, Stainless Steel
- Polypropylene, Hastelloy
- Polypropylene, PVDF
- Conductive Poly, Conductive Poly
Graco Husky 1050: Center Housing and Joint Design Eliminate Leaks
- Single piece center section eliminates leaks
- New robust square four-bolt joint design for even sealing pressure
Graco 1050: Poly and Conductive Poly have a new robust frame
- New structural frame
- Increased strength
- Decreased joint relaxation
- Fluid contact layer
- Chemically resistant materials
Husky 1050: Modular Air Valve
- Stall-free
- Low pulsation
- Fast change-over, quick snap pilot valves
- Optional "smarts" - pulse output, DataTrak (includes pulse output and runaway control)
- Complete redesign - the only shared parts between 1040 and 1050 are balls
Husky 1050: More capabilities
- Pulse output capability
- DataTrak, runaway control, pulse output
- Remote compatible with current Cycle-Flo
- Leak detection
- When operating the Husky 1050, turn your inlet air pressure down by 30-40% to match the fluid output of the Husky 1040
Up to five times the diaphragm life
- Bolt-through and over-molded options
- Re-engineered diaphragms and fluid covers to optimize efficiency
- Minimal deformation
Graco Expanding Blade Agitator
Graco's expanding blade agitators are engineered for quick installation and operation. The standard 1.5 and 2-inch threaded housing makes installation and operation as simple as threading on the agitator and adjusting the speed to the desired rate.
Features:
- SST Construction
- Standard 1.5 and 2-inch bung connections
- Adjustable blades for positioning within the tank
- Simple screw-in installation
Materials:
- Stain
- Paint
- Foam
- Polyurea
Applications:
- Wood
- General Metal
- Residential and commercial insulation
- Polyurea coating applications
- Sealed containers with 1.5 and 2-inch bung access